It takes 1.64 µs for the potential difference between the deflection plates to reach 60 volts.The electric potential difference across the capacitor and resistor will be equal to the applied potential difference, which is 100 volts.
Data from the question: Area of deflection plates = 10 cm x 2 cm = 20 cm²
Gap distance = 1 mm = 0.1 cm
Potential difference = 100 volts
Resistor = 925 ohm
We know that the capacitance of a capacitor can be given as,
C =ε₀A/d
Where, C = Capacitance, ε₀ = Permitivity of free space, A = Area of the capacitor plates, d = Gap distance between the plates.
Now, we can calculate the capacitance of the deflection plates as,
C = ε₀A/d = 8.85 × 10^-12 x 20 / 0.1 = 1.77 × 10^-9 F
Also, we know that,C = Q/V. Putting the given values in this equation,
1.77 × 10^-9 F = Q/100V
Thus, the charge on the plates can be given as,
Q = C × V = 1.77 × 10^-9 F × 100 V = 1.77 × 10^-7 C
Now, we know that Current I = V/R, Where V = Potential difference, R = Resistance. We can calculate the current flowing through the circuit as
I = V/R = 100/925 = 0.108 A
Now, we can calculate the time taken for the potential difference to reach 60 volts as,Q = It
Charge, Q = 1.77 × 10^-7 CT = Q/I = 1.77 × 10^-7 / 0.108 = 1.64 × 10^-6 s
Thus, it takes 1.64 µs. For the potential difference between the deflection plates to reach 60 volts. As the plates of the capacitor are connected to a resistor in series, we can assume that the potential difference across the capacitor is equal to the potential difference across the resistor. Therefore, the electric potential difference across the capacitor and resistor will be equal to the applied potential difference, which is 100 volts, after a long time.
Learn more about Potential difference at: https://brainly.com/question/12198573
#SPJ11
if the variable capacitor in an fm receiver ranges from 10.9 pf to 16.4 pf , what inductor should be used to make an lc circuit whose resonant frequency spans the fm band?
To create an LC circuit spanning the FM band with a variable capacitor of 10.9-16.4 pF, use the formula L = 1/(4π²f²C).
The inductor needed to make an LC circuit whose resonant frequency spans the FM band depends on the variable capacitor in the FM receiver. In your case, the variable capacitor ranges from 10.9 pF to 16.4 pF. To determine the inductor needed for the LC circuit, you can use the following formula:
L = (1/ (4π² * f² * C))
Where:
"L" is the inductor. "f" is the frequency of the LC circuit. "C" is the capacitor.For example, if you set the variable capacitor to 10.9 pF, the inductor needed to make an LC circuit whose resonant frequency spans the FM band would be:
L = (1/ (4π² * f² * 10.9 pF))
Learn more about circuit: https://brainly.com/question/29255502
#SPJ11
A bike accelerate uniformly from rest to a speed of 7.10m/s over a distance of 35.4m. Determine the acceleration of the bike
Answer: A
Explanation:
ferromagnetic materials lose their ability to form permanent magnets if select one: a. cooled below their curie temperature. b. heated above their curie temperature. c. aligned north and south. d. the electrons lose their spin magnetic moment.
Ferromagnetic materials lose their ability to form permanent magnets if b. heated above their curie temperature.
Ferromagnetic materials are a type of material that exhibits magnetism in the absence of an external magnetic field. Cobalt, nickel, and iron are the most commonly used ferromagnetic materials, although alloys such as Alnico are also used. A permanent magnet is a magnet that produces a magnetic field that does not change. A permanent magnet can be made from a ferromagnetic material. The strength of a permanent magnet is proportional to the amount of ferromagnetic material used.
Ferromagnetic materials lose their ability to form permanent magnets if they are heated above their Curie temperature. The Curie temperature is the temperature at which the ferromagnetic material's magnetic properties begin to deteriorate, and it loses its magnetism as a result. The magnetism of a ferromagnetic material is caused by the alignment of its magnetic domains. When the ferromagnetic material is heated to its Curie temperature, the thermal energy causes the domains to lose their alignment, causing the material to lose its magnetism.
Learn more about permanent magnet at:
https://brainly.com/question/6458972
#SPJ11
a microwave oven operates at 2.90 ghz . what is the wavelength of the radiation produced by this appliance?
The given frequency of a microwave oven is 2.90 GHz. We have to find the wavelength of the radiation produced by this appliance. The speed of light is a constant value of 3 x 108 m/s. The relation between frequency and wavelength of electromagnetic radiation is given by:
c = fλ
Where,
c = speed of lightf = frequency of radiationλ = wavelength of radiationWe can rearrange this equation to get the formula for wavelength:
λ = c / f
Substituting the given values, we get:
λ = 3 x 108 / (2.90 x 109)λ = 0.1034 m or 10.34 cmTherefore, the wavelength of the radiation produced by the microwave oven is 10.34 cm.
Learn more about microwave oven: https://brainly.com/question/3164926
#SPJ11
suppose a clay model of a koala bear has a mass of 0.195 kg and slides on ice at a speed of 0.65 m/s. it runs into another clay model, which is initially motionless and has a mass of 0.36 kg. Both being soft clay, they naturally stick together. What is their final velocity?
The final velocity of the two clay models after they stick together is 0.23 m/s.
To calculate this, we use the conservation of momentum equation:
Final Momentum = Initial Momentum
m₁v₁+ m₂v₂ = (m₁ + m₁) x v
Where m₁ and v₁ are the mass and velocity of the first object, and m₂ and v₂ are the mass and velocity of the second object.
Given question:
m₁ = 0.195kg
v₁ = 0.65m/s
m₂ = 0.36kg
v₂ = 0
Applying the given values:
m₁v₁+ m₂v₂ = (m₁ + m₁) x v
0.195kg x 0.65m/s + 0.36kg x 0 = (0.195kg + 0.36kg) * v
0,126 = 0.555v
v = 0,23 m/s
Thus, their final velocity is 0.23 m/s.
Learn more about momentum at https://brainly.com/question/402617
#SPJ11
put the processes that occur when oceanic plates spread apart at the mid-ocean ridge in order, from the first event at the top to the last event at the bottom.
a. Basaltic lava erupts from the rift.
b. Blocks of oceanic crust are downdropped in normal faults.
c. Sediment settles onto new basalt.
d. Oceanic crust has a smooth surface covered by layered sediment.
The following is the order of events that take place when oceanic plates spread apart at the mid-ocean ridge:
1. Basaltic lava erupts from the rift.
2. Blocks of oceanic crust are down-dropped in normal faults.
3. Sediment settles onto new basalt.
4. Oceanic crust has a smooth surface covered by layered sediment.
When an oceanic plate diverges from another oceanic plate or diverges from a continental plate, a mid-ocean ridge is created.
The mid-ocean ridge system is formed as magma rises from the mantle and is injected into the crustal rocks above.
The injection of magma creates a rift and extrusion of basaltic lava along the crest of the ridge.
The lava flows out from the crest of the ridge and cools and solidifies to form new crustal rock.
Thus, the first event that occurs when oceanic plates spread apart at the mid-ocean ridge is that basaltic lava erupts from the rift, and blocks of oceanic crust are down-dropped in normal faults.
As the new basaltic rock cools and solidifies, the sediment settles onto it. Finally, the oceanic crust has a smooth surface covered by layered sediment.
To know more about mid-ocean ridge:https://brainly.com/question/7666628
#SPJ11
In the video for Part B of this experiment, several chemical tests were performed to determine the identity of Sample X and Sample Y. Identify one reaction that was observed that pushed the reaction either in the forward or reverse direction by filling in the blanks in the statement given below. Identify what phenomenon occurred that caused the equilibrium to shift. Zn shot was added to the solution of 0.15 M CuCl2 in 2.5 M Naci, no reaction occurred betwee . This (Select) solution [ Select ] the concentration. This resulted in the equilibrium shifting in the [Select ] 4 direction. ILLIUn triat was obser that pushed the reaction either in the forward or reverse direction by filling in the blank the statement given below. Identify what phenomenon occurred that caused the equilib to shift.
No reaction took place after adding Zn shot to the 0.15 M CuCl2 in 2.5 M NaCl solution. The concentration was [raised] by this (heterogeneous) solution. The balance shifted in the reverse direction as a result.
What is equilibrium?
When a system is in a state of chemical equilibrium, neither the reactant concentration nor the product concentration changes over time, nor does the system exhibit any further changes in its attributes.
In the video for Part B of this experiment, the reaction observed is the displacement reaction of Zn and Cu2+. When Zn shot was added to the solution of 0.15 M CuCl2 in 2.5 M NaCl, no reaction occurred between them. This means the solution was not conductive enough for a reaction to take place. This resulted in the equilibrium shifting in the backward direction. The phenomenon that occurred that caused the equilibrium to shift is the Le Chatelier's principle. The addition of Zn metal caused the concentration of Cu2+ to decrease, causing the equilibrium to shift backward according to Le Chatelier's principle. According to Le Chatelier's principle, a system at equilibrium will respond to an external stress in such a way as to minimize the stress, as a result of which the equilibrium shifts in the forward or backward direction. The principle is applicable to any reversible reaction at equilibrium, no matter whether the system is gaseous, liquid or solid.
Learn more about equilibrium on
https://brainly.com/question/517289
#SPJ11
The distance between the centers of Earth and the Moon is D. If the mass of the Earth is Me and the mass of the Moon is MM, which of the following is a correct expression for the magnitude of the acceleration of an object that is located halfway between the two bodies, a distance 1/2D from their centers? a. 4G ( ME-MM)/D b. 2G (ME-MM)/D^2 c. G (ME + MM)/D^2 d. 2G (ME + MM)/D^2 e. 4G (ME + MM)/D2
The correct expression for the magnitude of the acceleration of an object that is located halfway between the centers of Earth and the Moon is (e) 4G (ME + MM) / D2.
The magnitude of the acceleration of an object between two objects due to their gravitational force is given by the formula:
a = GM / r²
where G is the universal gravitational constant,
M is the mass of the object that generates the gravitational field,
r is the distance between the object and the center of the object that generates the gravitational field.
The object is located halfway between the centers of Earth and the Moon at a distance of 1/2D from their centers. Hence, the distance between the object and Earth is D/2, and the distance between the object and Moon is also D/2.
The mass of Earth is Me and the mass of the Moon is MM.
The acceleration due to the gravitational force of Earth is:
a1 = GM / r1²
where r1 = D/2 and M = Me
The acceleration due to the gravitational force of the Moon is:
a2 = GM / r2²
where r2 = D/2 and M = MM
The net acceleration due to the gravitational force of Earth and Moon is given by:
a = a1 + a2
To calculate the acceleration:
a = GM / r2a
= G(M1 + M2) / r2²
Therefore, the net acceleration is:
a = G(Me + MM) / (D/2)²a
= 4G(Me + MM) / D2
The correct answer is (e) 4G (ME + MM) / D2.
To know more about gravitational force:
https://brainly.com/question/3009841
#SPJ11
when troubleshooting an hvac system, if no voltage is measured across any of the pairs of thermostat wiring terminals, the problem is most likely with the wire connected to terminal
When troubleshooting an HVAC system, if no voltage is measured across any of the pairs of thermostat wiring terminals, the problem is most likely with the wire connected to terminal C.
What is an HVAC system?HVAC stands for heating, ventilation, and air conditioning. An HVAC system is used to regulate indoor temperatures, humidity, and air quality. It may be used in residential, commercial, or industrial settings. HVAC systems can be complex, with various components and controls, and can require maintenance and repair from time to time.
When troubleshooting an HVAC system, there are several possible causes of a no-voltage problem, including: Tripped circuit breaker or blown fuse in the HVAC system or main electrical panel. Thermostat malfunction: faulty or damaged wiring or connections in the HVAC system, thermostat, or electrical panel.
Transformer failure or malfunction in this case, if no voltage is measured across any of the pairs of thermostat wiring terminals, the problem is most likely with the wire connected to terminal C. This could be due to a wiring or connection problem or a transformer failure or malfunction. A qualified HVAC technician should be consulted to diagnose and repair the problem.
Learn more about HVAC system here:
https://brainly.com/question/28235245
#SPJ11
what is the minimum initial height h of block 1 such that block 2 just makes it to the top of the loop without losing contact with the ramp? express your result in terms of any relevant quantities given in the problem (mb, r, g).
The minimum initial height h of block 1 such that block 2 just makes it to the top of the loop without losing contact with the ramp is given by the expression 2r + R as given below.
It is given that the system of the two blocks is released from rest at a height h above the bottom of the circular loop of radius R. As per the question, the minimum initial height h of block 1 such that block 2 just makes it to the top of the loop without losing contact with the ramp is to be calculated.The system is released from rest, thus the initial velocity of the system is zero. Due to this, the mechanical energy of the system will remain constant throughout its motion.
We can use the conservation of mechanical energy of the system to solve the problem. Conservation of mechanical energy of the system can be given as -mg (2r + R) + ½ mbv² + ½ mav² = -mgR. Where, mg (2r + R) is the gravitational potential energy of the system at point A when the blocks are at the height of h above the bottom of the circular loop of radius R. Here, a and b denote the velocities of the two blocks at point B when block 2 just makes it to the top of the loop without losing contact with the ramp.
The velocity of the blocks when block 2 just makes it to the top of the loop without losing contact with the ramp is zero. Hence, v = 0. The velocity of the block at the top of the loop is also zero. Thus, va = 0.The minimum initial height h of block 1 such that block 2 just makes it to the top of the loop without losing contact with the ramp is given by the expression 2r + R as given below.-mg (2r + R) + ½ mbv² + ½ mav² = -mgRv = 0, va = 0.
Thus, the minimum initial height h of block 1 such that block 2 just makes it to the top of the loop without losing contact with the ramp is given by the expression 2r + R.
Learn more about conservation of mechanical energy: brainly.com/question/19969393
#SPJ11
an ambulance truck emits sound with a frequency of 800hz. what is the frequency detected by a stationary observer if the ambulance truck is moving 30 m/s toward the observer? (the speed of sound in air at 20c is 343 m/s)
The frequency detected by a stationary observer if the ambulance truck is moving 30 m/s toward the observer is 731.3 Hz.
When the ambulance truck emits sound with a frequency of 800hz and the ambulance truck is moving 30 m/s toward the observer,
The observed frequency is given by the following formula.
f’ = f [(v ± v_o)/(v ± v_s)]
Where v = the speed of sound in air = 343 m/s
f = frequency of the source = 800 Hz
v_o = velocity of the observer (stationary) = 0 m/s
v_s = velocity of the source (ambulance truck) = -30 m/s (since the ambulance truck is moving toward the observer)
Now we can plug in the values into the formula and calculate the observed frequency.
f' = 800 ((343 - 30) / (343 + 0))
= 800 (313 / 343)
= 731.5 Hz (rounded to one decimal place)
If the ambulance truck is moving towards a stationary observer at a speed of 30 m/s, the frequency detected by the observer is 731.3 Hz.
To know more about "observed frequency" in physics: https://brainly.com/question/15056533
#SPJ11
The standard free energy for the reaction of oxygen binding to myoglobin Mb+O2(g)⇌ MbO2 is ΔG∘=−30.0kJmol−1 at 298 K and pH=7. The standard state of O2 is the dilute solution, molarity scale; therefore the concentration of O2 must be in M. What is the ratio MbO2/Mb in an aqueous solution at equilibrium with a partial pressure of oxygen pO2=400 Pa? Assume ideal behavior of O2 gas and for the protein in solution.
The ratio of MbO₂ to Mb at equilibrium with a partial pressure of oxygen pO₂ is 0.00002.
The ratio of MbO₂ to Mb in an aqueous solution at equilibrium with a partial pressure of oxygen pO₂ = 400 Pa can be calculated using the equation ΔG∘=−30.0 kJmol−1 at 298 K and pH = 7.
The equation used is: ΔG∘ = -RT ln (MbO₂/Mb), where R is the ideal gas constant and T is temperature in Kelvin. Rearranging this equation gives MbO₂/Mb = e^(-ΔG∘/RT).
Therefore, the ratio of MbO₂ to Mb at equilibrium with a partial pressure of oxygen pO₂ = 400 Pa is e^(-30.0/8.314*298) = 0.00002.
learn more about oxygen and solution at : https://brainly.com/question/1245440
#SPJ11
A ball is dropped from the top of a building. The height, y , of the ball above the ground (in feet) is given as a function of time, t (seconds) y = 1140 − 16 t 2 a) Find the velocity of the ball at time t . What is the sign of the velocity? Why is this to be expected? b) When does the ball hit the ground, how fast is it going at that time? Give answer in feet per second and in miles per hour.
the velocity of the ball at time t is -32t. And The negative sign indicates that the ball is moving downward at this speed, which makes sense because it is about to hit the ground.
How to find the velocity?
a) To find the velocity of the ball at time t, we need to take the derivative of the height function with respect to time:
y = 1140 - 16t²
v = dy/dt = -32t
So the velocity of the ball at time t is -32t. The negative sign indicates that the ball is moving downward. This is expected because the ball was dropped from the top of the building and is subject to the force of gravity, which pulls objects downward.
b) The ball will hit the ground when y = 0. We can use this fact to find the time when the ball hits the ground:
0 = 1140 - 16t²
16t²= 1140
t²= 71.25
t ≈ 8.43 seconds
So the ball will hit the ground after 8.43 seconds. To find the velocity of the ball at this time, we substitute t = 8.43 into the expression for velocity we found earlier:
v = -32t ≈ -269.76 feet per second
To convert this velocity to miles per hour, we can use the conversion factor 1 mile per hour = 1.46667 feet per second:
v ≈ -269.76 / 1.46667 ≈ -183.99 miles per hour
The negative sign indicates that the ball is moving downward at this speed, which makes sense because it is about to hit the ground.
To know more about velocity visit :-
https://brainly.com/question/80295
#SPJ1
A mass weighing 24 pounds, attached to the end of a spring, stretches it 4 inches. Initially, the mass is released from rest from a point 6 inches below the equilibrium position. Find the equation of motion. (Use g = 32 ft/s2 (for the acceleration due to gravity.)x(t) = _____ ft
The equation of motion , x(t) = -6 cos (6.71t) ft
The equation of motion for a mass attached to a spring is given by x(t) = A cos (ωt) + B sin (ωt), where A and B are constants, ω is the angular frequency, and x(t) is the displacement of the mass from its equilibrium position at time t.
Mass attached to spring weighs 24 pounds
Spring is stretched 4 inches when the mass is attached
The mass is released from a point 6 inches below the equilibrium position
Acceleration due to gravity is 32 ft/s²
From the information, it can be concluded that a mass of 24/32 = 0.75 slugs is attached to the spring, which has a spring constant k = (mg)/x = (0.75 × 32)/4 = 6 lbf/inches.
The equation of motion is given by,x(t) = A cos (ωt) + B sin (ωt)
Since the mass is initially released from a point 6 inches below the equilibrium position, the displacement at time t = 0 is given by x(0) = -6. Therefore,
x(0) = A cos (ω × 0) + B sin (ω × 0) = A
From the initial condition of zero velocity, the derivative of the displacement function is given by,
v(t) = -Aω sin (ωt) + Bω cos (ωt)
Since the mass is initially released from rest, the velocity at time t = 0 is given by v(0) = 0. Therefore,
v(0) = -Aω sin (ω × 0) + Bω cos (ω × 0) = Bω
Equating x(0) = -6 and v(0) = 0, we get, A = -6 and Bω = 0.
Since ω cannot be zero, we get B = 0.
Thus, the equation of motion is, x(t) = -6 cos (ωt)
Substituting x = 4 inches and T = 2π/ω, we get,
4 = -6 cos (ωT/2)
Solving for T, we get,T = 2.094 s
Substituting T and the value of g, the value of ω is calculated as, ω = 6.71 rad/s
Therefore, the equation of motion is, x(t) = -6 cos (6.71t) ft
Learn more about "Gravity and motion" at : https://brainly.com/question/2537310
#SPJ11
which of the following electric charge doesn't exist in nature? a. 8.00 cross times 10 to the power of negative 17 end exponent c b. 4.80 cross times 10 to the power of negative 19 end exponent c c. negative 2.40 cross times 10 to the power of negative 19 end exponent space c d. negative 1.60 cross times 10 to the power of negative 18 end exponent c
The electric charge that does not exist in nature is d. - 1.60 × 10⁻¹⁸ C.
What is an electric charge?
An electric charge is a basic property of matter that results from the presence or absence of electrons. Electrons are subatomic particle that makes up atoms. They are negatively charged and have a very small mass. An atom is neutral in its electrical charge since the number of electrons and protons in its nucleus is the same.
There are two kinds of electric charge: positive and negative.
The net charge on an object is the sum of all the charges on it, and it is either positive, negative, or neutral.
What is the electric charge that does not exist in nature?
Negative 1.60 × 10⁻¹⁸ C does not exist in nature because an electric charge is quantized in nature, which means that electric charge is always a multiple of the smallest electric charge unit (charge of an electron or proton).
The electric charge on a proton is equal and opposite to the electric charge on an electron.
Learn more about electric charge here:
https://brainly.com/question/26100412
#SPJ11
An elevator that has descended from the 50th floor is coming to a halt at the 1st floor. As it does, your apparent weight is:a) less than your true weight
b) equal to your true weight
c) more than your true weight
d) zero
Option a. When the elevator reaches the 1st floor and comes to a halt, your apparent weight will be less than your true weight.
The apparent weight of an object in an elevator is affected by the force of gravity, the mass of the object, and the acceleration of the elevator. In this case, the elevator is decelerating from the 50th floor to the 1st floor, which means the acceleration is negative. When the elevator reaches the 1st floor and comes to a halt, your apparent weight will be less than your true weight.
To illustrate this concept, consider Newton's Second Law of Motion which states that
Force = Mass x Acceleration (F = ma).
In this case, the force exerted by gravity on the object remains the same (its true weight) but the acceleration changes as the elevator descends. As the acceleration decreases, the apparent weight decreases accordingly.
Therefore, option a is correct.
Learn more about "Weight" and "gravity" at : 'Newton’s Laws of Motion' https://brainly.com/question/23011853
#SPJ11
air enters the compressor of a simple gas turbine power plant at 708f, 1 atm, is compressed adiabatically to 40 lbf/in.2, and then enters the combustion chamber where it burns completely with propane gas (c3h8) entering at 778f, 40 lbf/in.2 and a molar flow rate of 1.7 lbmol/h. the combustion products at 13408f, 40 lbf/in.2 enter the turbine and expand adiabatically to a pressure of 1 atm. the isentropic compressor efficiency is 83.3% and the isentropic turbine efficiency is 90%. determine at steady state(a) the percent of theoretical air required.(b) the net power developed, in horsepower.
In Isentropic turbine ,Net power developed = [(1/2.2) x (20,313 Btu/lbmol) x (1.7 lbmol/h)] / [(1.3558 x 10^5) x (0.903)] = 57.0 horsepower. Percent of theoretical air = 100 x [(1.7 lbmol/h)/(1.7 lbmol/h x [1/2.2])] = 77.3%
A) To determine the percent of theoretical air required, use the equation:
Percent of theoretical air = 100 x [(Actual mass of air used)/(Theoretical mass of air required)]
The theoretical mass of air required can be determined using the equation:
Theoretical mass of air = [(Mass of propane used)/(Combustion products of air-fuel ratio)]
The combustion products of air-fuel ratio can be determined by using the equation:
Air-fuel ratio = [Air/Fuel]
Using these equations, we can calculate the percent of theoretical air required:
Percent of theoretical air = 100 x [(1.7 lbmol/h)/(1.7 lbmol/h x [1/2.2])] = 77.3%
B) To determine the net power developed, in horsepower, use the equation:
Net power developed = [(Air-fuel ratio) x (Heat of combustion) x (Molar flow rate)] / [(1.3558 x 10^5) x (Thermal efficiency)]
Using these equations, we can calculate the net power developed:
Net power developed = [(1/2.2) x (20,313 Btu/lbmol) x (1.7 lbmol/h)] / [(1.3558 x 10^5) x (0.903)] = 57.0 horsepower.
For more such question on Isentropic turbine
https://brainly.com/question/14087805
#SPJ11
water is reabsorbed through specialized water channels called ______.
Water is reabsorbed through specialized water channels called aquaporins. Aquaporins are transmembrane proteins that are found in the plasma membrane of many types of cells, including those in the kidney, lungs, and salivary glands.
Aquaporins are specialized water channels that allow for the reabsorption of water. The plasma membranes of many different types of cells, including those in the kidneys, liver, lungs, and brain, include integral membrane proteins called aquaporins. By obstructing the passage of other molecules like ions and solutes, they give water molecules a chance to cross the membrane. Aquaporins are necessary for numerous physiological activities, including the concentration of urine and the preservation of cell volume and shape, and help control the body's water balance.
Learn more about specialized water here:
https://brainly.com/question/28097422
#SPJ4
An experimenter finds that standing waves on a string fixed at both ends occur at 12 Hz and 16 Hz , but at no frequencies in between. What is the fundamental frequency?
If the standing waves on a string fixed at both ends occur at 12 Hz and 16 Hz , but at no frequencies in between the fundamental frequency is 12 Hz.
The experimenter finds that standing waves on a string fixed at both ends occur at 12 Hz and 16 Hz, but at no frequencies in between. The fundamental frequency is the lowest frequency that can produce standing waves on the string. This is the frequency of the first harmonic or the first node.
The frequency of the first harmonic is given by the equation:
f1= v/2L
where f1 is the fundamental frequency, v is the velocity of the wave, and L is the length of the string.
Since the string is fixed at both ends, it is not vibrating at either end. Therefore, there is no antinode at either end. As a result, the fundamental frequency is the frequency at which the string vibrates as a whole with an antinode at the center.
The difference between the frequency of the second harmonic and the fundamental frequency is equal to the frequency of the first harmonic. In other words, the frequency of the second harmonic is twice the frequency of the first harmonic.
The difference between the frequency of the third harmonic and the frequency of the first harmonic is equal to the frequency of the first harmonic. In other words, the frequency of the third harmonic is three times the frequency of the first harmonic. This continues for higher harmonics.
Since the experimenter finds that standing waves on a string fixed at both ends occur at 12 Hz and 16 Hz, but at no frequencies in between, the frequency of the first harmonic is 12 Hz. Therefore, the fundamental frequency is 12 Hz.
Learn more about Fundamental frequency:
https://brainly.com/question/28169057
#SPJ11
an object starts from rest at when the object moves in the x direction with positive velocity after the instantaneous velocity and average velocity are related by (a) (b) (c) (d) can be larger than, smaller than, or equal to
When an object starts from rest, and it moves in the x direction with a positive velocity, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."
The rate at which an object moves in a given direction is known as velocity. It is a vector quantity that has a magnitude and a direction. For example, if an object moves 10 meters to the north in 5 seconds, the velocity is 2 m/s northward.Average velocity and instantaneous velocityInstantaneous velocity is the velocity of an object at a particular instant or point in time. In other words, it's the speed of an object at a specific moment. The average velocity is the total displacement divided by the total time taken for the motion. In other words, it is the total distance covered in a given direction over a specific time period.
The instantaneous velocity and average velocity are related by the inequality that can be larger than, smaller than, or equal to. The instantaneous velocity represents the velocity at a particular moment or point in time, while the average velocity represents the average velocity over a specified time period. The instantaneous velocity and average velocity can be different because the instantaneous velocity is the velocity at a specific moment, whereas the average velocity is the average of all the velocities over a given period of time. Therefore, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."
More on velocity: https://brainly.com/question/15721950
#SPJ11
Explain how a thermal cycler help the process of PCR can be used in the identification of a disease pathogen?
A thermal cycler is used in the process of PCR to amplify DNA samples, which can then be used to identify disease pathogens through genetic testing.
PCR, or polymerase chain reaction, is a laboratory technique used to amplify and copy DNA samples. It involves the use of a thermal cycler, which rapidly cycles through different temperatures to facilitate the various steps of the PCR process. The thermal cycler heats and cools the reaction mixture containing the DNA sample and other reagents, causing the DNA to denature, anneal, and elongate in a repeating cycle. Once the DNA has been amplified, it can be used in genetic testing to identify the presence of specific disease pathogens, such as viruses or bacteria, by comparing the amplified DNA sequence to known pathogen sequences.
To know more about pathogen, here
brainly.com/question/25411165
#SPJ4
What do you think would happen if a solid were exposed to extremely cold temperatures, or if a gas were exposed to extremely hot temperatures? Is it possible that there are more than three states of matter?
Solids can become Bose-Einstein condensates at very low temperatures, but gases may become plasmas at very high temperatures. There are further states of matter, such as quark-gluon plasma, and more states might be found.
Exposing a solid to extremely cold temperatures would cause its particles to slow down and reach minimal kinetic energy, resulting in a Bose-Einstein condensate. Conversely, exposing a gas to extremely hot temperatures would cause its particles to move faster, leading to dissociation into individual atoms and ionization into a plasma state. While solids, liquids, and gases are the most common forms of matter, there are other forms such as plasmas, Bose-Einstein condensates, and quark-gluon plasma that exist under extreme conditions. Ongoing research into potential new states of matter may lead to further discoveries in the future.
learn more about Bose-Einstein here:
https://brainly.com/question/12053772
#SPJ4
a voltage source is set at 36 volts. if you wanted to decrease the amount of current in a resistor from 120 amps to 80 amps by changing the voltage source, what should the new voltage setting be?
To decrease the amount of current in a resistor from 120 amps to 80 amps by changing the voltage source, the new voltage setting should be 24 volts. The relationship between voltage, current, and resistance is given by Ohm's law, which states that voltage (V) equals current (I) times resistance (R).V = IR
So, if the voltage source is set at 36 volts and the current through the resistor is 120 amps, we can find the resistance of the resistor using Ohm's law .R = V/IR = 36/120R = 0.3 ohms Now, if we want to decrease the current through the resistor to 80 amps, we can use the same formula to find the new voltage setting .V = IRV = 0.3 x 80V = 24 volts Therefore, the new voltage setting should be 24 volts to decrease the current through the resistor from 120 amps to 80 amps by changing the voltage source.
for such more questions on Ohm's law
https://brainly.com/question/14296509
#SPJ11
shown below is a small particle of mass 25.0 g that is moving at a speed of 9.3 m/s when it collides and sticks to the edge of a uniform solid cylinder. the cylinder is free to rotate about its axis through its center and is perpendicular to the page. the cylinder has a mass of 0.460 kg and a radius of 9.3 cm, and is initially at rest. what is the angular velocity of the system after the collision?
A small particle of mass 25.0 g that is moving at a speed of 9.3 m/s when it collides and sticks to the edge of a uniform solid cylinder. The cylinder is free to rotate about its axis through its center and is perpendicular to the page. the cylinder has a mass of 0.460 kg and a radius of 9.3 cm, and is initially at rest. The angular velocity of the system after the collision is 55.7 rad/s.
The angular velocity of the system after the collision is determined by the conservation of angular momentum. This law states that the total angular momentum of an isolated system remains constant; if a system has an initial angular momentum of 0, any change in angular momentum must be balanced by a corresponding change in the rotational speed of the system.
In this case, the initial angular momentum of the system is 0 since the cylinder is initially at rest. After the collision, the mass of the small particle can be considered to be moving in a circular path with a radius of 9.3 cm. This means the final angular momentum of the system is equal to the linear momentum of the particle times the radius of the cylinder: 25.0 g x 9.3 cm x 9.3 m/s = 21.0 kg m2/s.
The final angular velocity of the system is then equal to the total angular momentum divided by the total moment of inertia of the system: 21.0 kg m2/s / (0.460 kg x (9.3 cm)2) = 55.7 rad/s.
For more such questions on Angular velocity.
https://brainly.com/question/28146706#
#SPJ11
A survey was conducted at local colleges around Madison, Wisconsin to find out the average height of a college student. Of 692 students surveyed, 421 replied that they were over 6 feet tall. What is the standard error? Answer choices are rounded to the hundredths place.
A survey was conducted at local colleges around Madison where 692 students were surveyed, and 421 replied that they were over 6 feet tall showing a standard error of 0.0084 in the average height of a college student.
The standard error is given by the formula given below:
[tex]$$SE= {s}/{\sqrt{n}}$$[/tex]
Where s is the standard deviation,
n is the sample size.
Now let us find out the standard deviation by using the formula given below:
[tex]$$s=\sqrt{\frac{(421-271.17)^2+(271.17-270)^2}{692-1}}$$[/tex]
After calculating we get that the standard deviation s is equal to $0.2208$.
Now let us plug the value of the standard deviation s and sample size n into the formula for standard error:
[tex]$$SE={s}/{\sqrt{n}}$$[/tex]
On substituting the respective values, we get [tex]$$SE={0.2208}/{\sqrt{692}}$$[/tex]
On solving, we get that the standard error is equal to 0.0084
Therefore, the standard error is 0.0084.
Learn more about standard error: https://brainly.com/question/14467769
#SPJ11
A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Which of the following applications of the equation for the conservation of momentum represent the initial and final momentum of the system for a completely inelastic collision between the blocks? Justify your selection. Select two answers. A. 2Mo = 3Muf, because the blocks stick together after the collision.
B. 3Mvo = 3MUf, because the blocks stick together after the collision. C. 2MVo = 2MU + Muf, because the blocks stick together after the collision. D. 2MVo = M0o + 3 Muf, because the blocks do not stick together after the collision.
A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Thus, the correct options are A and B.
What is Momentum?The initial momentum of the system = the momentum of block 1 = (2M)vo. The final momentum of the system = the momentum of the combined blocks = (2M + M)uf = 3Muf. Therefore, the correct applications of the equation for the conservation of momentum that represent the initial and final momentum of the system for a completely inelastic collision between the blocks are:
2Mo = 3Muf, because the blocks stick together after the collision. 3Mvo = 3MUf, because the blocks stick together after the collision.
Therefore, the correct options are A and B.
Learn more about Momentum here:
https://brainly.com/question/30677308
#SPJ11
as a source of blackbody radiation becomes hotter, the peak in its radiation spectrum moves from the visible to the ultraviolet and beyond. does this imply that the object can no longer be seen by the unaided human eye
Yes, it is correct that when the source of blackbody radiation becomes hotter, the peak in its radiation spectrum shifts from the visible to the ultraviolet and beyond. Blackbody radiation is electromagnetic radiation emitted from a blackbody or perfect absorber. This is due to the fact that hotter objects emit shorter wavelengths of electromagnetic radiation, which correspond to higher energy photons. Therefore, when an object gets hot enough to emit mostly ultraviolet or X-ray radiation, it will no longer be visible to the unaided human eye because the human eye can only detect radiation within the visible spectrum of about 400 nm (violet) and 700 nm (red). Therefore, a blackbody that emits radiation beyond this range will no longer be seen by the unaided human eye.
For more information regarding this topic, you can click the below link
https://brainly.com/question/893656
#SPJ11
for the given input voltage amplitude (200 mvpp), what is the maximum gain that this amplifier will be able to produce? show your calculation below.
The maximum gain of an amplifier that produces an output voltage amplitude of 50 Vpp with an input voltage amplitude of 200 mVpp is 25. The formula to calculate gain is output voltage amplitude divided by input voltage amplitude.
In this case, we are given an input voltage of 200 mVpp, so the maximum gain of this amplifier can be calculated as follows:
Gain = Output Voltage/Input Voltage = Output Voltage/200 mVpp
Therefore, the maximum gain of this amplifier is equal to the output voltage. In other words, the maximum gain of this amplifier is equal to the voltage output of the amplifier.
To calculate the output voltage of the amplifier, we need to know the supply voltage and the resistance of the load. Assuming the supply voltage is 5V and the load resistance is 10k ohms, the output voltage can be calculated as follows:
Output Voltage = Supply Voltage * Load Resistance / (Load Resistance + Output Resistance) = 5V * 10k ohms / (10k ohms + 10k ohms) = 5V
Therefore, the maximum gain of this amplifier is 5V/200 mVpp = 25.
To summarize, the maximum gain of this amplifier is 25, calculated by dividing the output voltage by the input voltage. The output voltage can be calculated by knowing the supply voltage and load resistance.
For more such questions on Maximum voltage gain.
https://brainly.com/question/31086456#
#SPJ11
what current will this array draw from a 50.0 v battery having negligible internal resistance if we connect it across ab . express your answer with the appropriate units.
The current drawn from the 50.0 V battery across AB is 4.1667 A.
To solve the given question, we have to use the basic electrical circuit formula to find the current that the array will draw from a 50.0V battery if we connect it across AB. We are given a circuit diagram as follows: The formula used to find the current I is:
I = V/R
Where:
V is the voltageR is the resistance of the circuitWe have to find the equivalent resistance of the circuit across AB to find the current drawn from the battery. The equivalent resistance of the circuit is the sum of the resistances of the individual resistors. Thus, the equivalent resistance of the circuit is: R = 5 + 2 + 5R = 12Ω
Substituting the values of V and R in the formula above, we get:
I = V/R = 50/12 = 4.1667 AThus, the current drawn from the 50.0 V battery across AB is 4.1667 A.
Learn more about circuit: https://brainly.com/question/29255502
3SPJ11
Imagine another solar system, with a star of the same mass as the Sun. Suppose a planet with a mass twice that of Earth (2MEarth) orbits at a distance of 1 AU from the star. What is the orbital period of this planet? Hint: Think about how the mass of the Sun compares with the mass of the Earth. a. 3 months b. 6 months
c. 1 year d. 2 years
e. It would not be able to orbit at this distance.
The correct answer is option D.2 years
What is Kepler's third law of planetary motion?According to Kepler's Third Law of Planetary Motion, T² is proportional to r³, where T is the period of revolution of the planet and r is the distance between the planet and the star.
In order to solve for T,
AU = 1
Astronomical Unit = the average distance between the Earth and the Sun = 149.6 million kilometres
Therefore, the planet is orbiting at a distance of 149.6 million kilometres from the star.
Substituting the values of r and solving for
T².T² ∝ r³T² ∝ (149.6)³T²
= (149.6)³T²
= 3.522 x 10¹²T
= √3.522 x 10^¹²T
= 1.87 x 10⁶ seconds
T = 31,100 minutes
T = 518 hours
T = 21.6 days
T = 2 years
Therefore, the orbital period of the planet with twice the mass of Earth orbiting at a distance of 1 AU from a star with the same mass as the Sun is 2 years.
To know more about Kepler's third law of planetary motion:
https://brainly.com/question/4978861
#SPJ11