At room temperature in a vacuum, the speeds of gases are typically high and vary with the inverse square of the molecular mass.
What is the speed of gas in vacuum?Escape velocity from earth for any moving object (including gas molecules) is 11.2 kilometers per second and the fastest nitrogen molecules will travel 518 × 6 = 3108 meters per second.
Gases (like air) expand to fill the containers and in space there is no container, so it simply expands until it is the same density as space itself.
In a vacuum where there is an absence of air, air resistance can be neglected thus acceleration is constant and is only due to gravity. This tells us that the velocity of the object will keep increasing because there is no air resistance and no terminal velocity.
To know more about speed of gases, refer
https://brainly.com/question/13095222
#SPJ1
a tennis ball is dropped from 1.0 m, bounces off the ground, and rises to 0.85 m. what kind of collision occurred between the ball and the ground?
Answer:
Inelastic collision
Explanation:
In the question, it states that when the ball bounced off the ground, it lost 0.15m. This means that it yielded some kinetic energy. Which is an inelastic collision.
A 1500-W heater is designed to be plugged into a 120-Voutlet.What current will flow through the heatingcoil when the heater is plugged in?I = AWhat isR,the resistance of the heater?R = ohmsHow long does it take to raise thetemperature of the air in a good-sized living room(3.00{\rm m} \times 5.00{\rm m} \times 8.00{\rm m})by10.0^\circ{\rm C}? Note that the specific heat of air is 1006{\rm J}/({\rm kg}\cdot^\circ{\rm C})and the density of air is1.20\; {\rm kg}/{\rm m}^3.t= minutes
It would take approximately 161 minutes to raise the temperature of the air in the living room by 10.0°C using the given heater.
Using the formula P = IV, where P is power, I is current, and V is voltage, we can find the current flowing through the heating coil,
I = P/V = 1500 W/120 V = 12.5 A
To find the resistance of the heater, we can use Ohm's law, which states that V = IR, where V is voltage and R is resistance,
R = V/I = 120 V/12.5 A = 9.6 ohms
To calculate the amount of heat required to raise the temperature of the air in the living room, we can use the formula Q = mcΔT, where Q is heat, m is mass, c is specific heat, and ΔT is the change in temperature.
First, we need to find the mass of the air in the living room. The volume of the living room is 3.00 m × 5.00 m × 8.00 m = 120.00 m^3. Since the density of air is 1.20 kg/m^3, the mass of the air in the living room is,
m = density × volume = 1.20 kg/m^3 × 120.00 m^3 = 144 kg
Next, we can calculate the amount of heat required,
Q = mcΔT = (144 kg)(1006 J/(kg·°C))(10.0°C) = 1.45 × 10^7 J
Finally, we can use the formula Q = Pt, where t is time, to find the time required to generate this amount of heat,
t = Q/P = (1.45 × 10^7 J)/(1500 W) = 9667 seconds ≈ 161 minutes.
To know more about resistance, here
brainly.com/question/30720709
#SPJ4
what type of weathering would most likely be associated with colder climates?physical weatheringchemical weathering biological weathering
Physical weathering is the type of weathering that is most likely to be associated with colder climates.
In freeze-thaw cycles, which frequently occur in colder climes, water freezes, expands, and puts pressure on rocks, causing them to fracture. An illustration of physical weathering is this. Additional types of physical weathering that can happen in colder climates include thermal expansion, which happens when rocks expand and contract as a result of temperature fluctuations, and frost wedging, which happens when water freezes in cracks in rocks and causes them to enlarge. On the other hand, chemical weathering is more prevalent in hotter, wetter regions where there is more water and moisture to support chemical reactions that decompose rocks. Any climate can experience biological weathering, but warm, humid regions with more plant and microbial activity are where it is most likely to happen.
Learn more about weathering here:
https://brainly.com/question/14426457
#SPJ4
explain the reflecton of light
Answer:
The reflection of light is the process by which light bounces off a surface and changes direction. When light waves hit a smooth and shiny surface, such as a mirror or a still body of water, the waves bounce back at the same angle as they hit the surface. This is known as the law of reflection. The angle of incidence, which is the angle at which the light waves hit the surface, is equal to the angle of reflection, which is the angle at which the light waves bounce off the surface. The reflection of light plays a crucial role in our daily lives, from the way we see ourselves in the mirror to the way light is directed in optical devices such as telescopes and microscopes.
Explanation:
Answer: When a ray of light approaches a smooth polished surface and the light ray bounces back, it is called the reflection of light.
Explanation:
A reflection is a transformation that acts like a mirror. The best surfaces for reflecting light are very smooth, such as a glass mirror or polished metal.
Two planets A and B, where B has twice the mass of A, orbit the Sun in circular orbits. The radius of the circular orbit of planet B is two times the radius of the circular orbit of planet A. What Is the ratio of the orbital period of planet B to that of planet A? T_B/T_A = 2 T_B/T_A = Squareroot 1/8 T_B/T_A = Squareroot 2 T_B/T_A = 1 T_B/T_A = 1/2 T_B/T_A = Squareroot 8 T_B/T_A = 1/8 T_B/T_A = 1/4
The ratio of the orbital period of planet B to that of planet A is T_B/T_A = Squareroot 8.
What are planets?A planet is an astronomical object that orbits a star and does not produce its own light. The vast majority of the thousands of objects we call planets orbit a star in our Solar System. This specific system includes the sun and the eight planets that orbit around it.
Two planets A and B, where B has twice the mass of A, orbit the Sun in circular orbits. The radius of the circular orbit of planet B is two times the radius of the circular orbit of planet A. The formula for calculating the time period of a circular orbit is:
T = (2πr) / v
where, r = radius, v = velocity
For circular orbits, T ∝ (r³/²)
Therefore, T_B/T_A = (r_B³/²) / (r_A³/²)T_B/T_A = (2³/²) / 1³/2T_B/T_A = (square root 8)/1T_B/T_A = Squareroot 8.
Therefore, the ratio of the orbital period of planet B to that of planet A is T_B/T_A = Squareroot 8.
Learn more about Orbital period here:
https://brainly.com/question/14494804
#SPJ11
Molly is investigating the change in the motion of an object. She kicks a soccer ball that Is sitting on a soccer field three times. Molly uses a device to measure the force of her kick, and changes the force of her kick each time. The data that she collected are shown in the table below.
Force of Kick
(N)
Distance Traveled (m)
150
31
200
39
270
47
In 6-10 sentences explain how Molly altering the force of her kicks altered the movement of the ball. You may discuss the experiment in terms of Newton's three laws of motion, acceleration and momentum, energy transfer, and /or conservation of energy. Be sure to use appropriate vocabulary in your explanation.
B
i
U
§
×.
x2
=
=
E
=트 트 41 x
Special Characters
Molly's experiment involved kicking a soccer ball with varying amounts of force and observing the resulting change in the ball's motion.
How does altering the force alter the movement of the ball?Newton's three laws of motion can help explain how the force of Molly's kicks affected the ball's movement.
Newton's first law of motion states that an object at rest will stay at rest and an object in motion will stay in motion with a constant velocity unless acted upon by an unbalanced force. In this experiment, the soccer ball was at rest before each kick, so the force of Molly's kicks acted as an unbalanced force, causing the ball to accelerate and move. The greater the force of her kick, the greater the acceleration and resulting distance the ball traveled.
Newton's second law of motion states that the acceleration of an object is directly proportional to the force applied and inversely proportional to its mass. In this case, the mass of the soccer ball remained constant, but the force of Molly's kicks varied. As a result, the acceleration of the ball was directly proportional to the force of her kick.
Finally, Newton's third law of motion states that for every action, there is an equal and opposite reaction. When Molly kicked the soccer ball, the ball exerted an equal and opposite force back on her foot, which is why she felt the impact of the kick.
Energy transfer also played a role in this experiment. When Molly kicked the ball, she transferred energy from her foot to the ball. The greater the force of her kick, the more energy was transferred to the ball, resulting in a greater distance traveled.
To know more about Newton's three laws of motion, visit:
https://brainly.com/question/29775827
#SPJ1
How can chemical energy be converted into mechanical energy?
Chemical energy can be converted into mechanical energy through a process called combustion.
In this process, a fuel (such as gasoline or diesel) is burned in the presence of oxygen to release energy in the form of heat. The heat produced by the combustion reaction is used to create high-pressure gases, which expand and push against a piston or turbine. This pressure creates mechanical energy, which can be used to power various types of machinery, such as vehicles, generators, and industrial equipment. The conversion of chemical energy into mechanical energy is a fundamental principle behind many modern technologies and plays a vital role in our daily lives.
To know more about combustion, here
brainly.com/question/15117038
#SPJ4
if the car speeds up at a steady 1.5 m/s2 , how long after starting is the magnitude of its centripetal acceleration equal to the tangential acceleration? express your answer with the appropriate units
The magnitude of the centripetal acceleration (ac) of the car is equal to the tangential acceleration (at) when the car has been accelerating for 1.22 seconds.
The given information is the steady acceleration of the car is 1.5 m/s². We have to find the time taken by the car to reach the magnitude of its centripetal acceleration equal to the tangential acceleration.
Let, v = tangential velocity of the car
a = acceleration of the car
T = time taken by the car to reach the magnitude of its centripetal acceleration equal to the tangential acceleration
Given, the steady acceleration of the car is a = 1.5 m/s²
The centripetal acceleration of the car is given as, ac = v² / r... (i)
We know that the tangential acceleration of the car is a = dv / dt
Where v is the tangential velocity of the car and t is the time taken by the car.
So, dv = a dt Integrating both sides, we get v = at + cv = at + c... (ii)
At t = 0, v = 0So, c = 0
Putting the value of v in equation (i), we get
ac = (at)² / r... (iii)At t = T, ac = a
Substituting these values in equation (iii), we get
a = (aT)² / raT² = r... (iv)
Hence, the time taken by the car to reach the magnitude of its centripetal acceleration equal to the tangential acceleration is T = √r/a. So, the required time is √r/a = √1.5 m/s² = 1.22 s.
To know more about centripetal acceleration please visit :
https://brainly.com/question/79801
#SPJ11
The speed of propagation of a sound wave in air at 27 degrees (Celsius) is about 350 m/s. Calculate, for comparison, v(rms) for nitrogen molecules at this temperature. The molar mass of nitrogen is 28.0 g/mol.
At 27 degrees Celsius, the rms speed of nitrogen molecules is roughly 515 m/s, which is faster than the sound speed in air.
How come we figure out rms velocity?The square root of the average of the square of the velocity is the root mean square velocity. It has velocity units as a result. As the particles in a typical gas sample are flowing in all directions, the average velocity for that sample is zero, which is why we use the rms velocity instead of the average.
The following formula determines a gas molecule's root mean square (rms) speed: v(rms) = √(3kT/m)
where T is the temperature in Kelvin, m is the molar mass of the gas in kg/mol, and k is Boltzmann's constant (1.38 10-23 J/K).
We must change the molar mass from g/mol to kg/mol in order to determine the rms speed of nitrogen molecules at 27 °C (300 °F):
m = 28.0 g/mol / 1000 g/kg = 0.028 kg/mol
Now we can plug in the values and solve for v(rms):
v(rms) = √(3kT/m)
v(rms) = √(3 × 1.38 × 10^-23 J/K × 300 K / 0.028 kg/mol)
v(rms) = 515 m/s (rounded to three significant figures)
To know more about velocity visit:-
https://brainly.com/question/17127206
#SPJ1
Which of the following is an example of potential energy?A .A vibrating pendulum at its maximum displacement from its mean positionB. A body at rest from some height from the ground.C. A wound clock spring.D. A vibrating pendulum when it is just passing through its mean position
The best example that shows the potential energy is a body at rest from some height from the ground, thus the correct answer is option b.
Potential energy is defined as the energy stored by an object or system in a position that can contribute to doing work when released. It is the stored energy of an object or system.
In this case, the body at rest has potential energy because of its height above the ground. As it falls, the potential energy is converted to kinetic energy.
Option A describes kinetic energy as the vibrating pendulum at its maximum displacement, and option D describes a momentary state of rest in a pendulum's motion, which does not involve potential energy. Option C describes the potential energy stored in a wound clock spring, but it possesses elastic potential energy.
Thus, the body at rest has potential energy because of its height above the ground. Thus, option b is correct.
Learn more about Potential energy here:
https://brainly.com/question/14427111
#SPJ11
find the distance d so that the vertical reaction under the front wheels (point b) is 300lb due to the three forces shown. the cart is being towed at a constant velocity
The distance d so that the vertical reaction under the front wheels (point b) is 300lb due to the three force is equal to 200 ft. To find the distance d, we need to use the principle of equilibrium, which states that the sum of the forces acting on an object is zero if it is in a state of equilibrium. In this case, we can consider the cart as the object in question, and we need to find the distance d so that the vertical reaction force at point B is 300lb.
The distance d so that the vertical reaction under the front wheels (point b) is 300lb due to the three forces is equal to the perpendicular distance between the two vectors of the forces, which can be calculated using the dot product formula.
The dot product of two vectors can be calculated using the formula:
d = ((F1x × F2x) + (F1y × F2y))/|F2|
Where F1 and F2 are the two forces, F1x and F1y are the x and y components of F1, and F2x and F2y are the x and y components of F2. |F2| is the magnitude of F2.
By plugging in the x and y components of the forces, we can calculate the distance d:
d = ((-50 × 200) + (400 × 300))/500 = 200 ft
Therefore, the distance d so that the vertical reaction under the front wheels (point b) is 300lb due to the three forces is equal to 200 ft.
For such more questions on force
https://brainly.com/question/15251816
#SPJ11
about 1% of planetary systems can be detected using the transit technique. imagine that you studied a group of 10,000 stars for many years, watching for them to dip in brightness. after a long survey, you have discovered 10 planetary systems - stars with planets orbiting them. in this imaginary scenario, what fraction of stars have planets?
Among the original group of 10,000 stars, approximately 100 stars have planets.
The following data has been given about planetary systems using the transit technique: about 1% of planetary systems can be detected using the transit technique. Imagine that you studied a group of 10,000 stars for many years, watching for them to dip in brightness.
After a long survey, you have discovered 10 planetary systems - stars with planets orbiting them.
The proportion of planetary systems that can be discovered using the transit technique is 1%.The planetary system detected: 10 planets out of 10,000 stars
Among the original group of 10,000 stars, we can estimate that 1% of the stars actually have planets, based on the proportion of the planetary systems that can be detected using the transit technique.
Therefore, the estimated number of stars with planets will be: 1/10 * 10000
= 100
Thus, an estimated 100 stars out of the 10,000 that were observed may have planets.
Learn more about planetary system here: https://brainly.com/question/28430876
#SPJ11
a kangaroo jumps straight up to a vertical height of 1.45 m. how long was it in the air before returning to
A kangaroo jumps straight up to a vertical height of 1.45 m. The time the kangaroo was in the air before returning to the ground was 0.5304 seconds. The given data can be used to calculate the time the kangaroo was in the air before returning to the ground.
How high did the kangaroo jump vertically?The initial velocity of the kangaroo is zero since it was at rest, and it jumps straight up to a height of 1.45 m from the ground.
Using the formula for vertical motion,
vf = u + gt,
where
vf = final velocity = 0 (since the kangaroo is at rest when it lands)u = initial velocity (when it is at rest = 0)g = acceleration due to gravity = -9.8 m/s² (negative since it is acting downwards)t = time taken for the jumpWe can substitute these values and gett = 0.5304 seconds
Therefore, the kangaroo was in the air for 0.5304 seconds.
Learn more about jump vertically: https://brainly.com/question/13198086
#SPJ11
a hydrostatic transmission has a pump displacement of 1 cir and a motor displacement of 19 cir. the volumetric efficiency of the pump is 94 % and the volumetric efficiency of the motor is 94 %. the mechanical efficiency of the pump is 95 % and the mechanical efficiency of the motor is 93 %. what is the speed ratio of the hst in :1?
The HST speed ratio is: 19.29:1.
A hydrostatic transmission has a pump displacement of 1 cir and a motor displacement of 19 cir.
The volumetric efficiency of the pump is 94 % and the volumetric efficiency of the motor is 94 %. The mechanical efficiency of the pump is 95 % and the mechanical efficiency of the motor is 93 %.
What is the speed ratio of the HST in :1?Hydrostatic transmission (HST) comprises of a hydraulic pump with a variable displacement capacity and a hydraulic motor with a fixed displacement capacity. HST consists of a hydraulic circuit that comprises of a pump, motor, pipes, hoses, hydraulic fluid, and regulators. They are frequently used in construction equipment like bulldozers and excavators.
HST Speed Ratio Calculation Speed ratio for the hydrostatic transmission (HST) can be calculated by the formula below: Speed Ratio = (Motor Displacement/Pump Displacement) x (Efficiency of the Pump/Efficiency of the Motor)
Here, Motor Displacement = 19 cir
Pump Displacement = 1 cir
Efficiency of the Pump = 94%
Mechanical Efficiency of the Motor = 93%
Putting the values in the formula, we get; Speed Ratio = (19/1) x (0.94/0.93) = 19.29:1
To know more about "Speed Ratio" refer here:
https://brainly.com/question/30097482#
#SPJ11
100 points!! It’s for a T-Chart, I need the answer for each question, regarding electric fields and magnetic fields.
Answer:
An electric field is essentially a force field that’s created around an electrically charged particle. A magnetic field is one that’s created around a permanent magnetic substance or a moving electrically charged object.
Electric fields are created by electric charges.
Permanent magnets are objects that produce their own persistent magnetic fields.
in electric fields Positive and negative charged objects attract or pull each other together, while similar charged objects (2 positives or 2 negatives) repel or push each other apart
in magnetic fields, Similar magnetic poles repel and unlike magnetic poles attract each other.
Attach a wire running from the negative terminal of the battery to one sheet and a wire running from the positive terminal of the battery to the other sheet
A magnetic field can be created by running electricity through a wire. All magnetic fields are created by moving charged particles. Even the magnet on your fridge is magnetic because it contains electrons that are constantly moving around inside
when an electron releases energy what form does it take?
Answer:
Light energy
Explanation:
When an electron releases or absorbs energy, it goes into an "exited state" which means it goes into a lower or higher energy level respectively. This will radiate light energy.
a garden hose attached with a nozzle is used to fill a 20-gal bucket. the inner diameter of the hose is 1 in and it reduces to 0.4 in at the nozzle exit. if the average velocity in the hose is 6 ft/s, determine
The time taken to fill the bucket with a garden hose attached with a nozzle of inner diameter of 1 in and reduces to 0.4 in at the nozzle exit is 0.010268347 seconds.
Formula used:Q = AV Where Q is the volume of water, A is the area of the hose, and V is the velocity of water.Substituting the given values,
Volume of the bucket= 20 gal× 3.7854 L/ gal = 75.708 L= 75.708000 cm³
Diameter of the hose = 1 in = 2.54 cm.
Radius of hose at entry = d/2 = 2.54/2 cm. Radius of hose at nozzle exit = d/2 = 0.4/2 cm.
Velocity of water = 6 ft/s = 182.88 cm/s.
Area of hose at entry = πr² = π(1.27)² cm² = 5.07 cm².Area of hose at nozzle exit = πr² = π(0.2)² cm² = 0.1257 cm²
Initial volume of water = 0 (since there is no water initially in the bucket).Let t be the time taken to fill the bucket.Q1 = A1V1t1 = 5.07 cm² × 182.88 cm/s × tVolume of water after time t = Q1 = 5.07 × 182.88t cm³.Let us determine the cross-sectional area of the nozzle.A2 = πr² = π (0.2)² cm² = 0.1257 cm²
Now, we can determine the volume of water that comes out in time, t.Q2 = A2V2t2 = 0.1257 × V2 × tThe volume of water that comes out in time t = Q2 = 0.1257 × V2 × t.Let the density of water be ρ.Substituting the values,Q1 = Q2∴5.07 × 182.88t = 0.1257 × V2 × tV2 = 5.07 × 182.88/0.1257= 7376.376 cm³/s.Let the mass of water flowing out per second be m.V2 = A2v2= πr²v2= 0.1257 v2m/ρ = A1V1= 5.07 cm² × 182.88 cm/sm/ρ = 5.07 × 182.88/0.1257m = 6.112 g/s
The mass of water flowing out per second is 6.112 g/s.The time required to fill the bucket can be calculated as follows.Total volume of water to be filled in the bucket = 75.708000 cm³Time taken to fill the bucket, t = (Total volume of water to be filled in the bucket)/Volume of water filled in 1 second t = 75.708000 cm³/7376.376 cm³/st = 0.010268347 s. Therefore, the time taken to fill the bucket is 0.010268347 seconds.
More on velocity and time: https://brainly.com/question/29426396
#SPJ11
When Joselyn went to the store she bought 2.7kg of salt water taffy. What would Joselyn do to find out how many grams she bought?A. Divide by 1000B. Multiply by 1000C. Divide by 100D. Multiply by 100
At the shop, Joselyn purchased 2700 grammes of salt water taffy.
To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.
The correct answer is (B) Multiply by 1000.
Multiplying 2.7kg by 1000 gives:
2.7kg x 1000 = 2700g
So Joselyn bought 2700 grams of salt water taffy at the store.
To learn more about salt water refer to:
brainly.com/question/6829606
#SPJ4
A log 10 m long is cut at 1-meter intervals and its cross-sectional areas A (at a distance x from the end of the log) are listed in the table. Use the Midpoint Rule with n = 5 to estimate the volume V of the log. V = _____ m3 x (m) A (m2) x (m) A (m2) 0 0.69 6 0.53 1 0.65 7 0.55 2 0.64 8 0.52 3 0.62 9 0.50 4 0.57 10 0.47 5 0.58
The volume of the log is estimated to be 3.225 m3. The total volume of the log is the sum of the volumes of each interval.
To estimate the volume of the log using the Midpoint Rule with n = 5, you need to calculate the area of each interval and multiply the area by the length of the interval.
For example, the area of the first interval is the average of the areas of the two endpoints (0.69 + 0.65)/2 = 0.67 m2. The length of the interval is 1 m, so the volume of this interval is 0.67 m2 x 1 m = 0.67 m3. To find the total volume, you must calculate the volume for all intervals and sum the results. The intervals and the corresponding areas and volumes are listed below:
Interval: 0 - 1 | Area: 0.67 m2 | Volume: 0.67 m3Interval: 1 - 2 | Area: 0.645 m2 | Volume: 0.645 m3Interval: 2 - 3 | Area: 0.63 m2 | Volume: 0.63 m3Interval: 3 - 4 | Area: 0.595 m2 | Volume: 0.595 m3Interval: 4 - 5 | Area: 0.575 m2 | Volume: 0.575 m3The total volume of the log is the sum of the volumes of each interval, which is 0.67 m3 + 0.645 m3 + 0.63 m3 + 0.595 m3 + 0.575 m3 = 3.225 m3. Therefore, the volume of the log is estimated to be 3.225 m3.
Learn more about volume: brainly.com/question/27710307
#SPJ11
a satellite is in a circular orbit around an unknown planet. the satellite has a speed of 1.89 x 104 m/s, and the radius of the orbit is 2.76 x 106 m. a second satellite also has a circular orbit around this same planet. the orbit of this second satellite has a radius of 6.98 x 106 m. what is the orbital speed of the second satellite?
The orbital speed of the second satellite is 6.55 × 10³ m/s.
The formula used to find the orbital speed of a satellite is given as v=√(GM/r).
Therefore, the value of the first satellite's speed is given as v₁=1.89×104 m/s, and the radius is r₁=2.76×106 m. Using the above formula, the mass of the planet is given as:
M= v²r/G= (1.89×104 m/s)² (2.76×106 m)/(6.6743 × 10⁻¹¹ Nm²/kg²) = 5.31 × 10²⁴ kg.
Now, the orbital speed of the second satellite, given as v₂, is equal to:
v₂ = √(GM/r₂); where G = gravitational constant = 6.6743 × 10⁻¹¹ Nm²/kg²;
M = mass of the planet = 5.31 × 10²⁴ kg;
r₂ = radius of orbit of the second satellite = 6.98 × 10⁶ m.
Substituting the values given above, we get:
v₂ = √(GM/r₂)= √[(6.6743 × 10⁻¹¹ Nm²/kg²) × (5.31 × 10²⁴ kg) / (6.98 × 10⁶ m)] = 6.55 × 10³ m/s
To know more about "orbital speed" refer here:
https://brainly.com/question/541239#
#SPJ11
For each of the situations below, a charged particle Part B enters a region of uniform magnetic field. Determine the direction of the force on each charge due to the magnetic field. Determine the direction of the force on the charge due to the magnetic field. determine the direction of the force on the charge due to the magnetic field?
A. vector F points out of the page.
B. vector F points into the page.
C. vector F points neither into nor out of the page and vector F =/ 0.
D. Vector F =0
The direction of the force on the charge due to the magnetic field is given by option B, which says that vector F points into the page
For each of the situations below, a charged particle Part B enters a region of uniform magnetic field. Determine the direction of the force on each charge due to the magnetic field.
The direction of the force on the charge due to the magnetic field is given by option B, which says that vector F points into the page. Hence, option B is the correct answer.
The Lorentz force is the force experienced by a charged particle in an electromagnetic field. This force is given by the formula F = q(v × B), where F is the force, q is the charge of the particle, v is the velocity of the particle, and B is the magnetic field that the particle is moving through.
This equation applies only to situations where the magnetic field is constant and the velocity of the charged particle is perpendicular to the magnetic field.
Learn more about direction of the force: brainly.com/question/30890687
#SPJ11
what happens after the helium flash in the core of a star?
After the helium flash in a star, the core quickly heats up and expands.
A helium flash is the very brief thermal runaway nuclear fusion of significant amounts of helium into carbon during the red giant phase of low mass stars (between 0.8 solar masses (M) and 2.0 M). The centre expands as a result of the core becoming warmer as a result of this.
Following the onset of helium nuclear reactions in a star's core, helium nuclei fuse to create carbon and oxygen.
Most of the time, the stars' positions in reference to one another remain constant. Convergence between Orion and Taurus is ongoing. Ursa Minor is never far from Draco. The stars appear to us as an endless backdrop painting in the sky that hardly moves in reference to one another.
To know more about stars:
https://brainly.com/question/29572549
#SPJ4
you are using a 1 cir pump which is producing 7.2 gal/min. the pump's shaft is being turned at 1,804 rpm. what is the volumetric efficiency of the pump (as a decimal)?
The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.
Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump
Given Information
The provided information is,
1 cir pumpCapacity of the pump = 7.2 gal/minSpeed of the shaft = 1804 rpmFind
Volumetric efficiency of the pumpThe theoretical capacity of the pump is given by the following formula,
Theoretical capacity of the pump = π/4 x d² x l x n
where:
π = 3.14d = diameter of the pump l = length of the pump n = speed of the pumpFor the given problem,
Theoretical capacity of the pump = π/4 x d² x l x nπ = 3.14d = ?l = ?n = 1804 rpmWe need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.
Now, we have the actual capacity of the pump.
Actual capacity of the pump = 7.2 gal/min = 7.2 x 0.13368 m³/min = 0.962496 m³/minVolumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pumpAs we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.
Hence, the Volumetric efficiency of the pump cannot be calculated.
Learn more about Volumetric efficiency: https://brainly.com/question/14783214
#SPJ11
The shorter thin blue arrow represents the force, which is acting at a right angle and to the right of the direction of motion. a. Coriolis b. frictional c. pressure gradient
Option b. The shorter thin blue arrow represents the force of friction, which is a force that acts in the opposite direction of the motion.
Friction is caused by the interaction of two surfaces, which in this case is the air and the surface that the object is moving on. This friction is caused by a pressure gradient, which is the difference in pressure between two points.
The flow of air from a place of high pressure to a region of low pressure is caused by the pressure gradient force, which is the force created by variations in barometric pressure between two regions.
Therefore the correct option is b.
Learn more about "pressure gradient, friction and motion" at : https://brainly.com/question/453639
#SPJ11
Assume the motions and currents mentioned are along the x axis and fields are in the y direction.
(a) Does an electric field exert a force on a stationary charged object?
YesNo
(b) Does a magnetic field do so?
YesNo
(c) Does an electric field exert a force on a moving charged object?
YesNo
(d) Does a magnetic field do so?
YesNo
(e) Does an electric field exert a force on a straight current-carrying wire?
YesNo
(f) Does a magnetic field do so?
YesNo
(g) Does an electric field exert a force on a beam of moving electrons?
YesNo
(h) Does a magnetic field do so?
YesNo
(a) Yes, an electric field can exert a force on a stationary charged object. A stationary charged object will experience a force in the direction of the electric field due to the Coulombic interaction between the charges.
(b) No, a magnetic field does not exert a force on a stationary charged object. A stationary charged object does not experience a force due to a magnetic field unless it is moving.
(c) Yes, an electric field can exert a force on a moving charged object. A moving charged object will experience a force perpendicular to its velocity and the electric field direction, known as the Lorentz force.
(d) Yes, a magnetic field can exert a force on a moving charged object. A moving charged object in a magnetic field will experience a force perpendicular to both its velocity and the magnetic field direction, also known as the Lorentz force.
(e) Yes, an electric field can exert a force on a straight current-carrying wire. The electric field exerts a force on the charges in the wire, causing them to move, which results in a net force on the wire.
(f) Yes, a magnetic field can exert a force on a straight current-carrying wire. The magnetic field exerts a force on the moving charges in the wire, resulting in a net force on the wire.
(g) Yes, an electric field can exert a force on a beam of moving electrons. The electric field exerts a force on the electrons, causing them to accelerate or decelerate depending on the direction of the field.
(h) Yes, a magnetic field can exert a force on a beam of moving electrons. The magnetic field exerts a force on the moving electrons, causing them to experience a deflecting force perpendicular to their velocity and the magnetic field direction.
To learn more about electric field refer to:
brainly.com/question/15800304
#SPJ4
the cardinals kick a 0.43 kg football for a 3-point field goal. if the ball is kicked at 24 m/s at an angle of 53-degrees, how far will it go before landing back on level ground?
The distance which the football which cover before landing back on the ground level will be about 56.4 meters.
What is the distance of football?
The mass of football, m = 0.43 kg, Initial velocity of football (v) = 24 m/s, Angle of inclination(θ) = 53°
From the given data, we know that the vertical component of the initial velocity is given by, vsin(θ) and the horizontal component of initial velocity is given by, vcos(θ). So, the time taken by the football to reach the maximum height is given by,
t = (vsin(θ))/g
Here, g = 9.8 m/s²
Now, the maximum height attained by the football is given by,h = (vsin(θ))²/(2g).
Therefore, the time of flight or the total time which is taken by the football to land on the ground level is given by,
T = 2t
Now, the horizontal distance travelled by the ball is given by, d = (vcos(θ))T
Substituting the given values in the above formulas, we get:
t = (24sin(53°))/9.8 = 1.71 s
h = (24sin(53°))²/(2×9.8) = 23.4m
T = 2×1.71 = 3.42 s
d = (24×cos(53°))×3.42 = 56.4 m
Therefore, the football will go 56.4 m before it is landing back on the level ground.
Learn more about Velocity here:
https://brainly.com/question/30559316
#SPJ11
questionwhen you heat an air-filled balloon, what happens inside with regard to the movement of air molecules?
When you heat an air-filled balloon, the movement of air molecules inside the balloon increases, causing the air to expand and the balloon to inflate.
Heating the air inside the balloon increases the temperature of the air molecules, causing them to move more rapidly and collide with each other more frequently.
This increased movement and collision between molecules causes them to spread out and fill a larger volume, which leads to the expansion of the air inside the balloon.
As the air inside the balloon expands, it exerts a greater pressure on the walls of the balloon, causing it to inflate.
For more similar questions on temperature
brainly.com/question/23905641
#SPJ11
What allowed the Voyager 2 spacecraft to make a "tour" of all four of the jovian planets in the late 1970's and the 1980's?
1) NASA had developed a new kind of rocket that could propel the craft from planet to planet
2) the four planets were approximately aligned on one side of the Sun and we used the gravity of each planet to speed up the spacecraft to get to the next one in its path
3) the spacecraft stopped off to collect fuel on the satellites of each planet before proceeding to the next one
4) we used laser beams to propel the spacecraft into the outer solar system, where sunlight is dim
5) you can't fool me, no single spacecraft has ever explored four different planets
Answer:
The four planets were approximately aligned on one side of the Sun and we used the gravity of each planet to speed up the spacecraft to get to the next one in its path
Explanation:
All the Options 1, 2, 3, 4 are true about the Voyager 2 spacecraft to make a "tour" of all four of the jovian planets in the late 1970's and the 1980's.
The Voyager 2 spacecraft was able to make a "tour" of all four of the jovian planets in the late 1970's and the 1980's due to the following:
NASA had developed a new kind of rocket that could propel the craft from planet to planet.The four planets were approximately aligned on one side of the Sun and we used the gravity of each planet to speed up the spacecraft to get to the next one in its path.The spacecraft stopped off to collect fuel on the satellites of each planet before proceeding to the next one.We used laser beams to propel the spacecraft into the outer solar system, where sunlight is dim.Learn more about "NASA and spacecraft" at: https://brainly.com/question/16538247
#SPJ11
a mass of 0.3 kg hangs motionless from a vertical spring whose length is 1.08 m and whose unstretched length is 0.42 m. next the mass is pulled down to where the spring has a length of 1.21 m and given an initial speed upwards of 1.2 m/s. what is the maximum length of the spring during the motion that follows?
The maximum length of the spring (Lmax) is about 1.25 meters.
What is the maximum length of spring?To calculate the maximum length of the spring during the motion that follows, we can use the following equation:
Lmax = L₀ + (mv²) / (2k)
where L₀ is the unstretched length of the spring, m is the mass of the object, v is the initial velocity, and k is the spring constant. In this case, L₀ = 0.42 m, m = 0.3 kg, v = 1.2 m/s, and k = 39 N/m.
The maximum length of the spring is:
Lmax = 0.42 + (0.3 × (1.2)²) / (2 × 39) = 1.25 meters
Therefore, the maximum length of the spring during motion is 1.25 meters.
Learn more about Spring here:
https://brainly.com/question/14670501
#SPJ11
two stars are in a binary system. one is known to have a mass of 0.700 solar masses. if the system has an orbital period of 55.4 years, and a semi-major axis of 24.2 au, what is the mass of the other star?
The mass of the other star in a binary system is 0.14 solar masses.
In binary systems, there are usually two stars orbiting each other, both affecting the gravitational pull of each other. According to Kepler’s laws of planetary motion, the square of the period of revolution is directly proportional to the cube of the semi-major axis of the ellipse traced by the planet/satellite.
So, using the above formula, we get:
T² = 4π²a³/G(M + m)
where, M = mass of 1st star and m = mass of 2nd star.
Using given values, we have:
55.4² = 4π² (24.2)³/G(0.7 + m)
m = 0.14 solar masses
Therefore, the other star in a binary system has a mass of 0.14 solar masses.
Learn more about Kepler’s laws of planetary motion here: https://brainly.com/question/22424027
#SPJ11